A little help please... Strange error...

[bbsux]

(I don't mess around much with S2 SA's. I use S2 Dtivo's personal and S1's for security recorders.)

Ok, have a tcd24XXX with lifetime (and a sdh400, with just tivo basic, but I am using each units own drive to copy to new drive) that I am upgrading from a 250 gig to a 750.

I copy to the new drive.

The drive is recently upgraded to 8.1a - ready to be hacked.

I run my home made script to copy over (killinitrd'ed 7.2.2 kernel copied off cd, new rc.sysinit.author, new iptables, delete netfilter-enable, copy AIO tools and extract) I usually leave the rest to do over serial or network.

BUT, if I connect my linksys 200m adapter it errors out and reboots.
Will boot fine without it attached. BUT if I wait to connect it until boots it will error and reset when I attach it. (I even tried an older usb1.1 linksys 100m adapter but the tivo acts like it isn't there.)

I tried this with both units and it did the same thing.

Its probably something simple, can you guys help me out?

I see insmod in the error, could it be a driver error? Do I need to install the backported drivers?

attached are my logs and script file, and rc.sysinit.author (script shows renaming netfilter, but I delete it manually same with iptables)

Thanks guys...

Log error with linksys attached:
PCI: 00:0d.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correctin
g to 32
hub.c: port 1, portstatus 501, change 1, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1, portstatus 503, change 10, 480 Mb/s
usb.c: USB device 2 (vend/prod 0x77b/0x2226) is not claimed by any active driver
.
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
hub.c: port 5, portstatus 100, change 0, 12 Mb/s
Unable to handle kernel paging request at virtual address 00000090, epc == c01da
f78, ra == c01daf68
Oops in fault.c::do_page_fault, line 213:
$0 : 00000000 00000000 000000c2 80b48006 80b48076 ffffffff 00000000 b001fc01
$8 : 00000004 801230cc 00000001 801f02a0 0000001f ffffffff 00000b48 80151b64
$16: c01db5fc 00000000 80b48000 80df6d40 8037f400 80f691a0 00000000 c01c41d0
$24: 00000000 b001fc01 802dc000 802ddd58 c01b30f8 c01daf68
Hi : 00000000
Lo : 00000000
epc : c01daf78 Tainted: P
Status: b001fc03
Cause : 0000000c
Process insmod (pid: 165, stackpage=802dc000)
Stack: 80151d98 00000081 00000000 8162a060 80151b64 000001d2 802ddda8
c00b486c c0088c2c c00b486c c0177224 c00b47d8 c01dbcd8 c01dbac4 80df6d40
c01dbcf8 00000000 8037f400 c01b3438 800476c4 00000001 7fff6b70 c00946a4
c0094618 8037f428 00000000 c01b32b4 00000000 8037f400 c01b2fb4 80feb000
00000060 10015100 80b2dca0 00000006 c01b3038 c01b32b4 00000000 8037f600
c01b2fb4 ...

Trace: c01daf78 c01b3438 c01b3038 c01b3074 c01b21a8 c01b210c c01db458 8002aacc
80020f64 020d8f4c
Code: 00409021 8c51006c 240200c2 <ae220090> 262300c8 262400d4 262500e0 3c02
c01e 2442a004
Kernel panic: Die called

<0>Rebooting in 1 seconds..


Log error after attached when booted:
rc.sysinit is complete
bash-2.02#
bash-2.02# hub.c: port 1, portstatus 501, change 1, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1, portstatus 503, change 10, 480 Mb/s
usb.c: USB device 2 (vend/prod 0x77b/0x2226) is not claimed by any active driver
.
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
hub.c: port 5, portstatus 100, change 0, 12 Mb/s
Unable to handle kernel paging request at virtual address 00000090, epc == c01da
f78, ra == c01daf68
Oops in fault.c::do_page_fault, line 213:
$0 : 00000000 00000000 000000c2 8065c406 8065c476 ffffffff 00000000 9001fc01
$8 : 00000004 801230cc 0000218b 801f02a0 0000001f ffffffff 80fc5b94 00000004
$16: c01db5fc 00000000 8065c400 814115c0 80b43400 80cb8b20 00000000 c01c41d0
$24: 00000000 80135f40 80fc4000 80fc5d58 c01b30f8 c01daf68
Hi : 00000000
Lo : 00000400
epc : c01daf78 Tainted: P
Status: 9001fc03
Cause : 0000000c
Process insmod (pid: 291, stackpage=80fc4000)
Stack: effca2f1 047c8026 6112f691 7d6fa5d6 eff7555c a68fd2fd 529f15ca
750700e7 ae33155d e2aac616 a6c105a8 efe1db98 c01dbcd8 c01dbac4 814115c0
c01dbcf8 00000000 80b43400 c01b3438 c474c118 c96217f9 a3b1e377 ce4ea464
e0183d8a 80b43428 00000000 c01b32b4 00000000 80b43400 c01b2fb4 81634000
00000060 10015100 81411780 00000006 c01b3038 c01b32b4 00000000 812e2400
c01b2fb4 ...

Trace: c01daf78 c01b3438 c01b3038 c01b3074 c01b21a8 c01b210c c01db458 8002aacc
80020f64 020d8f4c
Code: 00409021 8c51006c 240200c2 <ae220090> 262300c8 262400d4 262500e0 3c02
c01e 2442a004
Kernel panic: Die called

<0>Rebooting in 1 seconds..

[Jamie]

This issue is covered here (http://www.dealdatabase.com/forum/showthread.php?t=51874).

[bbsux]

Thanks... its hard to search when you don't know what to call it.

[bbsux]

Trying to hack my 240080 with lifetime. I've copied over the backported drivers and I'm stumped -- it looks like a tivoapp error. But why? I haven't even got that far yet...

First temperature parameters set:
Terminal temp: 71
Critical temp: 62
Logging temp: 60
Target temp: 50
Lowest fan speed: 7
/tvbin/fancontrol is running in the background.
Starting TvLauncher
assert: Tmk Assertion Failure:
assert: TmkServer, line 379 ()
Tmk Fatal Error: Activity TvBusProxy <87> strayed!
Paste the following into a shell to get a backtrace...

bt -t /tvbin/tivoapp <<END_OF_BT
tcd 1
hpk Series2
build b-8-1-mr @255458 2007.01.19-1830 release-mips []
pack 8.1a-01-2
read 0x00400000 /tvbin/tivoapp
read 0x02000000 /lib/libc.so.6
read 0x02200000 /lib/libm.so.6
read 0x02400000 /lib/libpthread.so.0
read 0x02600000 /lib/libutil.so.1
read 0x02800000 /lib/libtvutil.so
read 0x02a00000 /lib/libtmk.so
read 0x02c00000 /lib/libtvstructures.so
read 0x2aaa8000 /lib/ld.so.1
read 0x2ab04000 /lib/libhpkoss.so
read 0x2ab50000 /platform/lib/libhpkhl.so
read 0x2abf0000 /platform/lib/libhpkll.so
read 0x2ac34000 /lib/libdl.so.2
0x02a82758 0x02a86d48 0x02a25f30 0x02a50b54 0x00676e04 0x02a2a518 0x02a2a144
0x02a5fe60 0x02a2a02c 0x02a29f40 0x02a2c94c 0x02a3e070 0x02a3df58 0x02a3de08
0x02a3d394
END_OF_BT

Tmk Fatal Error: Activity TvBusProxy <87>: assertion failure
Waiting for launcher to start.
Launcher is running.
Scanning for phase2 repair scripts
Running boot Stage E_PreApplication scripts
Checking for database conversions
flushing ide devices: hda
Restarting system.

[jt1134]

Throw export TIVO_ROOT=
export MFS_DEVICE=/dev/hda10 into your rc.sysinit.author

[Jamie]

Did you replace /sbin/iptables as described here (http://www.dealdatabase.com/forum/showthread.php?p=204669#post204669)? If so, double check it is exectable, has unix line endings, etc. Your crash looks exactly like the one that results from using the stock iptables.

[bbsux]

I thought I did. I put it in my "copy over" script.

[bbsux]

Isn't amazing how the little things can screw you up? Thanks guys...